An Owner's Opinion Of Two Portable Planers I recently purchased a DeWalt DW733 12 1/2' portable planer. This purchase was made under duress.

At the time I owned a Delta 22-540 12' portable and was so disgusted with its excessive sniping that I was almost afraid to spend more than 83 cents on another portable planer. As is often pointed out by other woodworkers you can engineer and build infeed/outfeed tables and extensions, bolt the Delta 540 down, put your left hand over your right eye while standing on 1 foot, and reduce the amount of snipe on the 540. I'm joking of course but not to far from the truth. I tried a lot of these snipe-eliminating suggestions and did succeed in reducing the amount of snipe, but what I was getting was still unacceptable to me.

Additionally, my 'portable' planer now took up as much shop space as my table saw. I have limited shop space and one of the reasons the portable was attractive to me is that I could sit it on a shelf then pull it out and use it when I needed it. I should also point out that I understand this snipe problem is not particular to the Delta 540 but exists in all of the 'first generation' portables. I'm a hobbyist and spend more time picking my lumber, planning my cut strategy, and trying to optimize my yield than a professional shop would. I had always used my Dad's old planer that doesn't snipe at all. Denon Dct A100 Manual Dexterity.

I was taught to cut rough lumber to ¼-½' over finished size and then plane. This allows me to plane different parts of the same board to different thickness. It also helps to maximize cupped lumber because I can cut my narrower parts from these boards, rip and crosscut them close to final size, run these smaller easier to handle boards over the joiner taking off less lumber to get a flat side, then plane. Well I moved 700 miles from Dad's planer and that's when I bought the Delta 540. I quickly realized that with this planer I had to plane all of my wood in advance so that I would only lose 6' of each board to snipe. If I tried to work the way I was used to (and believe in) I had to cut each piece 6' longer than finished size – not a viable option for someone trying to optimize their lumber usage.

Since the first time I used the 540 I hated it but I didn't return it because I didn't have the money or space for a 15' stationary planer, I needed to plane lumber, and I understood from reading and talking to others that this was 'normal' for portable planers. I guess I'd just have to learn to deal with the waste but it irritated me every time I used it. In my opinion the purpose of a thickness planer is to plane boards to a consistent thickness for the length of the board.

Lots of people are happy with these machines and get defensive when I express my disgust (something I've been very vocal about). People also continue to recommend to others that they buy these planers. I've heard things like: 'You can build this to lessen the snipe' What if you bought a table saw and to get it to perform acceptably you had to make modifications, add pieces, re-engineer it, and it was still only OK – not Great? Would you be happy with it and recommend that table saw to others? 'What's the big deal with snipe? – just deal with it' – What if you bought a band saw and every time you cut a board on the band saw it ruined 6 inches of the length of the board. Would you say 'I love my Brand X band saw, and I recommend it highly'?

Dewalt Dw733 Manual Pdf Dewalt DW675 Pdf User Manuals. View online or download Dewalt DW675 Instruction Manual. Need to fix your DW733 Type 1 12 1/2 inch Planer? An owner's review of the new Dewalt Portable Planer. I'd like to be able to say that at this point I thoroughly read the owners manual. My new DeWalt DW733 is a.

'I can't afford to buy a better planer' Now you can! I had to plane about 100 b.f. Of maple and some oak during the upcoming weekend and was dreading losing about 10% of my expensive lumber to snipe. After agonizing over parting with $450 I made a decision. Digital Everywhere Firedtv Drivers there.

I'll go to Home Depot and buy the new highly touted DeWalt DW733 planer. First of all HD has a 30 day money back guarantee and so does DeWalt. I had already compared the DeWalt to the new Delta 560. And for a number of reasons I felt the DeWalt was a much better machine (plus Delta had already ticked me off with the 540 and I really didn't want to give them any more of my money for a portable planer). I got home and hesitantly unpacked the new yellow monster.

I was completely prepared to run screaming back to HD and demand my money back if something even hinted of snipe. I was also mentally preparing myself for this not working and having to spend $1000 or more for a 15' planer.

The planer was securely packaged and in perfect order when I dragged it from the box. I sat it on a Workmate™ and inspected it.

I was impressed with the fit and finish and everything was ready to go – no assembly required. The cutterhead assembly rides on 4 substantial steel posts. I familiarized myself with all of the controls, clamped it down, and turned it on. Pretty loud, but I don't think quite as loud as my 540. I'd like to be able to say that at this point I thoroughly read the owners manual. I grabbed a piece of scrap pine about 3' long x 6' wide cranked the planer to height and fed it through. Hummm – no snipe.

I was thinking this must have been a mistake and cranked to take another 1/32' off. No snipe again – OK I'm starting to get excited. I proceeded to plane that pine board down to less than a ¼' thick, I took off more than 1/16th on one pass. I never got any snipe. There's a pretty nifty 'Stock removal gauge' on the front of the cutterehead/motor assembly that gives you a rough idea how much you're taking off with each pass. I doubt if this thing is pinpoint accurate but it worked. Still pessimistic, I thought OK, that was pine and a short board.

Keep in mind that I hadn't even adjusted the infeed/outfeed tables. This was right out of the box. I grabbed 3 red oak boards 4/4 rough, each 8' long and varying widths from about 6' to 10'.

I planed those boards down to ¾' in the wink of any eye. The 15amp motor has plenty of power and I was able to take off 1/16th at a pass without tearout (or course these were brand new knives). I only took off about 1/32 for the final passes. I finally got some snipe.

On a couple of the passes I forgot to lock the cutterhead. The cutterhead lock is one new feature that is responsible for eliminating the snipe. The lock is operated by raising/lowering a bar right above the motor on the feed side. It's very handy and quick to operate but takes a little getting used to. You flip up the bar to unlock the cutterhead, make the height adjustment with the turn crank, then flip the bar back down to re-lock. When I forgot to lock the cutterhead the planer sniped almost as bad as my old 540 – proof positive that the cutterhead lock does its job. All of the controls on the DeWalt are very well thought out and convenient.

The crank handle is big and easy to grab hold of but folds down flat for storage. ¼ turn takes off 1/64th and the amount removed with each ¼ turn is printed on a disk at the bottom of the handle. There is a unique 'turret' style depth stop that has 3 settings similar to a depth stop on a plunge router. The ¾' stop was set accurately on mine from the factory. I got the dust hood, which is made from formed sheet metal, not plastic. The hood bolts to a metal shroud on the back of the cutterhead.

When I hooked the planer up to my 2hp dust collector something started flapping around the dust hood and made a really irritating noise. I found that air was being drawn in between the hood and the shroud and the hood side was flapping like the reed on a duck call. A piece of electrical tape fixed this.

Although I used 4' pipe to my DC, the hood also comes with a reducer from 4' to 2.5' to fit most shop vacs. The dust collection worked amazingly well, and I just had some minor sweeping at clean up time. The hood costs and extra $30. I haven't changed the knives yet. The DeWalt uses the 'old' style knife lock with a rigid clamp the entire length of the knife and quite a few bolts along the clamp to hold it in place. A knife height gauge and wrench to change knives are included and clip into a handy little storage try on the outfeed side of the cutterhead assembly.

The following Saturday I planed that 100 b.f. Of maple in precut pieces.

I never experienced any snipe and the machine performed flawlessly. Throughout this article where I say 'no snipe' I mean either virtually no snipe, or snipe so minimal it is almost imperceptible, and comes out easily with normal finish sanding. The Delta 22-540 is gone – good riddance. I sold it instead of beating it to smitherines with a sledge hammer like I wanted to. My new DeWalt DW733 is a pleasure to use and I recommend it unconditionally. I now work in a snipe-free environment.

– Dave Warren, 8/1/97.

I’m new to this forum, and noticed a whole lot of discussions on the dw733, but no answer to my problem. I would greatly appreciate anyone’s input on this. Yesterday while planing a piece of oak I heard a rattling sound, and before I could turn it off it was obvious the motor was spinning but the blades were not. The roller blades still work and it ejected the piece. After taking the side cover off I found that the belt was partly melted, the pulley on the cutter head was not bolted down, and there was evidence of metal shaving. Upon closer inspection the pulley is a little bent, where there was a tiny little piece of metal I found out was called a key.

This was lying at the bottom of the planer. The bolt that holds on the pulley I can’t find anywhere So, it seems the bolt came loose, the tension from the belt yanked the pulley out of allignment, ejecting the key and bending the slot it sits in in the pulley, the belt rubbed against something stationary at velocity and melted the edge off. All this without visibly damaging the cutter head, blowing the motor or hitting a knife!!! I looked up all the parts and can get everything near there, including the belt, for about $60. So now it looks like this is something I can tackle, but the dang pulley can’t disengage from the cutter head as it is blocked by the threaded height rod! Did they do this on purpose?!

I can’t replace the pulley without disassembling the entire machine, it appears. I’m concerned that once I start breaking this thing down I’ll never get it put back together in perfect allignment, and a planer that isn’t perfectly alligned is a really expensive paperweight! Has anyone ever tackled this job or anything like it to where they had to disassemble the planer, and were you successful?

Any tips, tricks or warnings? -- I keep cutting this d__n board and it's STILL too short!!! Thanks both of you for nudging me along! It wasn’t too big of a deal to get that threaded height rod out of the way, just had to detach the chain under the unit, brace the unit, and twist it out. I’m just waiting for the parts to come in the mail now.

The disruption to my project prompted me to allign and wax my joiner, sharpen a few blades, allign my table saw trade a blade out on my bandsaw, and come up with more projects for myself! Oh the joys of cabinetry, turns out you have to be a mechanic too, which was never my favorite thing! -- I keep cutting this d__n board and it's STILL too short!!! Well the reassembly went fine, got it alligned and it’s running great.

Getting that belt on the pulleys is a bear! I figured out in putting it back to gether that by placing two boards of exact same dimension on either side of cutter, turning the threaded height rods by hand until you have the cutter parallel to the bed, you can then tighten down the chain drive underneath the unit, ensuring a level cutter. The manual doesn’t describe making this adjustment, but it’s easy to do, just a couple of set screws holding on the chain pulleys underneath. There’s a dab of thread lock on them that doesn’t seem to be doing it’s job as there was no issue loosening. So if ever you notice your boards coming out uneven, this is how to adjust it. -- I keep cutting this d__n board and it's STILL too short!!! Have your say.

Forum Topics Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project. 11878 On the lathe, by the lathe: do you have questions? This forum is for all the woodturners out there. 1977 Relief, 3D, chip-carving, whittling; carving knives, chisels, pocket-knives, power tools. If you are a carver or want.

415 Intarsia, fretwork, intricate design cutting and more! This forum is for scrollsawers: share your tips, ask questions. 325 Have a question? A tip/strategy to share? A challenge, perhaps? Share your 'joinery' discussion here. 1289 The finish, whether paint, wax, stain, or something else, can make or break a project.

What are your tips and questio. 4715 Looking for information on designing your projects? Having difficulties reading project plans? Looking for help with. 6527 Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be.

27332 Questions and answers about CNC machines, tooling, best practices, and projects. 195 Wood, your hand tools, you and a little know-how. Share your questions, tips and strategies for the use and maintenan. 5258 Using a jig is like having a couple extra hands helping out. Show us your jigs, share your tips, strategies and, of c.

1373 Different wood requires different woodworking strategies - from cutting to finishing. Share your tips and challenges.

6075 Before you pick up those woodworking tools, take the time to ensure your safety in the shop! Eyes, ears, fingers, and. 1347 Are you looking for or do you have tips to share regarding the workshop? Storage, equipment placement, efficiency, an. 2085 If you are selling your work, then you have entered a woodworking dimension with added complexity and stress.

1170 All of us are holding onto treasure in our shops, that we either don't need, don't want, or could part with if presen. 4676 Connect with the Website Gurus and tell us what you are thinking, suggestions, problems, functionality issues, and so. 2181 Need a break from all the standing and wood dust?

Chat with your Forum Friends about their projects, their life, thei. Author Latest activity New comments or replies since you last checked 04:02 PM to get readership tracking 04:02 PM to get readership tracking 04:00 PM to get readership tracking 03:59 PM to get readership tracking 03:59 PM to get readership tracking 03:57 PM to get readership tracking 03:57 PM to get readership tracking 03:57 PM to get readership tracking 03:57 PM to get readership tracking 03:55 PM to get readership tracking • • • • • • • • • • • • • • • • ©2018 Verticalscope Inc. All Rights Reserved. DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.